Brushless Motor Controller with Stepless Speed 3650, 3525, 2430, 2418 Series 3-Phase Motor Model NFP-PWM-BLDC-3650
$8.00
Discover the power of our Brushless Motor Controller! Ideal for safe operation when properly used within specified limits. Buy now and enjoy!
BLDC PWM Reduction Gear Motor Speed Control Performance
- The motor is not allowed to exceed the limit load and stalled.
- The positive and negative poles of the circuit board power supply cannot be reversed, otherwise the chip will be burned.
- Reasonable selection of power supply according to the product input voltage (DC: DC 12V/24V).
- When approaching/exceeding the limit load torque, it may cause internal damage. Please use it reasonably
- Decreasing the motor speed will result in a decrease in output torque.
- There will be DB noise when the motor is running, and it will change slightly with the speed/load changeFunction: Forward and reverse, switching, stepless speed regulation, braking (requires the motor to have its own braking function).
| Model | NFP-PWM-BLDC-3650 |
|---|---|
| Length | 69mm |
| Width | 32mm |
| Load Voltage Range | 6V – 30V DC |
| Speed Regulation | Stepless |
| Default Frequency Position | 20KHz |
| Apply To | 3-phase brushless motor |
| Weight | appr.16g |
Brushless Gear Motor Text Module Technical Wiring Diagram
- Use For 2418 / 2838 / 4260 / 3650 / 3525 / 2430 / 3-phase brushless motor series.
- Default position is 20KHz, the 2 needle by the speed control knob is 2KHz.
- Smooth speed control, energy efficiency, compact design.
| Pin NO | SIGNAL | I/O | Specification | Remark |
|---|---|---|---|---|
| 1 | VCC | IN | DC 12V (operating range: 8V~15V) | Red wire, motor power supply |
| 1 | VCC | IN | DC 24V (operating range: 8V~26V) | Red wire, motor power supply |
| 2 | GND | IN | Ground | Black wire, Ground |
| 3 | CW&CCW (Input Voltage) | IN | 0~5.0V | Orange wire, CCW/CW Select |
| 3 | CW&CCW (VIH) | IN | Min 1.5V | CCW, High=CCW |
| 3 | CW&CCW (VIL) | IN | Max 0.6V | CW, Low=CW |
| 4 | FG (VOH) | OUT | 1.5V≤U≤5.0V, at 5V | Yellow wire: NPN open collector output for detecting rotation speed via FG phase shift. |
| 4 | FG (VOL) | OUT | Max 0.6V | Yellow wire: NPN open collector output for detecting rotation speed via FG phase shift. |
| 4 | FG (Signal Current) | OUT | Max 3mA | Yellow wire: NPN open collector output for detecting rotation speed via FG phase shift. |
| 4 | FG (Output Pulse) | OUT | 9 pulse | Yellow wire: NPN open collector output for detecting rotation speed via FG phase shift. |
| 5 | PWM (Input Voltage) | IN | 0~5.0V | White wire |
| 5 | PWM (VIH) | IN | Min 1.5V | Motor stop, High=stop |
| 5 | PWM (VIL) | IN | Max 0.6V | Motor running, Low=start |
| 5 | PWM (PWM Frequency) | IN | Advised 20KHz~30KHz |
Note:
- VCC and GND can not be used interchangeably.
- Please switch CW/CCW after the motor is fully stopped to avoid any damage.
- How to start the motor: Red wire to positive, black and white wires to GND. If CCW direction: Connect blue wire to low level power. If CW direction: Connect black, white, and orange wires to low level power.
2418/2430 general wiring instructions:
Black wire: Negative pole of motor power supply
Red wire: Positive pole of motor power supply
Yellow wire: Speed signal output (18 pulses are output for one revolution of motor)
White wire: Motor stepless speed regulation port: Input PWM, the duty cycle is inversely proportional to the speed, connected to the power supply, connect negative pole is the highest speed.
Orange wire: Motor forward and reverse control: when the port is not connected, the motor is CCW, and the port is connected to low level (≤0.6V) motor CW
3525/3650 general wiring instructions:
Black wire: Negative pole of motor power supply
Red wire: Positive pole of motor power supply
Yellow wire: FG signal output (for external equipment to detect motor speed, three pairs pole magnetic ring motor turn a circle to output nine square wave pulses
White wire: Motor forward and reverse control: when the port is not connected, the motor is CCW, and the port is connected to low level (≤0.6V) motor CW
Blue wire: Speed regulation control: speed regulation by inputting analog voltage, the speed is proportional to the voltage
2838 general wiring instructions:
Black wire: Negative pole of motor power supply
Red wire: Positive pole of motor power supply
Yellow wire: FG signal output (for external equipment to detect motor speed, three pairs pole magnetic ring motor turn a circle to output nine square wave pulses
White wire: Motor forward and reverse control: when port is not connected, the motor is CCW, and the port is connected to low level (≤0.6V) motor CW
Bule wire: Speed regulation control: Reverse speed regulation through PWM mode; connect to the negative pole of the power supply at full speed (maximum speed)
4260 general wiring instructions:
Black wire: Negative pole of motor power supply
Red wire: Positive pole of motor power supply
Yellow wire: FG speed signal output (for external equipment to detect the motor speed, two pairs of pole magnetic ring motor turns a circle and outputs six square wave pulses)
White wire: Motor forward and reverse control: when the port is not connected, the motor is CCW, and the port is connected to low level (≤0.6V) motor CW
Blue wire: Speed regulation control: Speed regulation by inputting analog voltage (0-5V); Speed and voltage proportional.
BLDC High Power Motor Driver Module Dimension
Keywords:
brushless motor regulator, high power motor drive controller, switch drive module
Sampling quantities for stocked models are available for ordering directly from us online.
Engineering & Manufacturing:
Please contact one of our Sales Engineers for a quotation for production and consultation for customization and integration services.
Payment Method:
Payment methods : Paypal or T/T
Shipping Method:
1.Delivery: DHL door to door 5-7days.
2.Item will be shipped within 1-3 business days after the payment.
3.If you haven’t received the item on the Delivery Time, pls contact us by email if you have any questions. Normally, we will give you a reply within 24hours, if not, pls check the spam of your email box. We will do our best to help you solve the problems.
4.Please make sure your address is matched with the finally shipping address before you pay.
5.In order to ensure you receive your order tax free upon import, we will declare it with a lower value, pls be noted ,thanks!
FAQ - Frequently Asked Questions
Q: If customized, what information should you provide?
A: You need to provide the basic specification of the motor, such as: Dimensions, Sizes Applications, Voltage, Speed and Torque. It's better to offer application prototype drawings to us if possible.
Q: What's your main motors?
A: Diameter 4mm~42mm Dc Micro Motor And Gear Motor, Auto Dc Motor, Electric Motor, Gear Motor, Mini Dc Motor, Brush Dc Motor, Brushless Dc Motor, Spur Gear Motor, Micro Motor, Vibration Motor Etc.
Q: What's the main application of the micro dc motor?
A: Our mini DC motors are widely used in Home Applications, Office Equipment, Health-Care Application, Sanitation Industry, High-Class Toy, Banking System, Electronic and Electrical Tools, Automation Industry, Bank Equipments, Payment Equipments, Vending Machines, Power Door Lock, Electric Door Lock.
Free Shipping Site-wide When You Spend More Than $150
Related products
-
3A 12V 24V DC Motor Speed Controller PWM Reversing Model NFP-PWM-CCM2
$10.00 Add to cart -
DC Motor Speed Controller Compatible with 12V 24V 36V 48V Motor Model NFP-PWM-CCM6DS
$10.00 Add to cart -
Remote Control Switch DC Motor Driver Model NFP-PWM-GV-DJ402S
$10.00 Select options -
Stepless Speed Regulator Switch 6V 12V 24V Driver Board Model NFP-PWM-CCM6C
$10.00 Add to cart
Still Can't Find Ideal Motors?
Get A Quote Within 8 Hours Contact Now! Any question about Micro DC Motor, Spec, Data-Sheet, Quote...
If you want a custom lead wire connection of the water resistant vibration motors. Such as alternate lead wire length & strip lengths, with a connector (e.g. Molex, JST). You can contact us from the footer form, tell us your need. Any problems will be taken seriously and will be answered professionally, so pls do not hesitate to contact us by the footer form.
Reviews